ER-Dynamically Tuned Gyro For Oil And Gas
ER-E1 Gyroscope for Downhole Survey
ER-E1 is with small size and strong shock resistance. It can be used for the system which with small space, was widely used in borehole gyro survey tools and well logging tools. It is designed for dynamical orientation and positioning in the drilling field.
Specifications:
No | Parameter | specification |
1 | Random Drift (1σ) | ≤0.5°/h |
2 | Drift unrelated with acceleration | ≤100°/h |
3 | Quadrature acceleration drift rate | ≤15°/h/g |
4 | Axial mass unbalance drift rate | ≤15°/h/g |
5 | Drift caused by axial acceleration | ≤10°/h/g |
6 | The motor power | exclusive use electrical power supply |
7 | Annunciator power | 3.5V 8KHz Single phase sine wave power consumption≤1W |
8 | Torque scale factor | ≤3mA/(°/s) |
9 | Linearity | ≤0.2%(F.S) |
10 | Measuring range | ±270°/s |
11 | Cross coupling error | ≤0.2% |
12 | Convergence time of open loop oscillation | 1.5s~2.5s |
13 | Operating temperature | -55℃~+85℃ |
14 | Vibration power spectral density | 0.16g2/Hz |
15 | Shock | 200g |
16 | Dimension | Φ21.8×18 mm Flange:22×22 mm |
17 | Weight | ≤45g |
ER-E2 Gyroscope for dynamic well logging
ER-E2 is specially designed for borehole drilling field which has overcame the following technical difficulties, especially its operating temperature up to 100 degree centigrade. Inertial devices are more adaptable and better applied in the drilling field than they are in aviation field due to its ability of working in poor conditions. The life of DTG and its adaptation in temperature are specified, especially when it was used in higher temperature.
Specifications:
N0. | Item | Specification | |
1 | Performance Parameter | Random Drift (1σ) | 0.3°/h |
Drift Stability (1σ) | ≤0.2°/h | ||
g-independent | ≤20°/h | ||
g-dependent | ≤3°/h | ||
Frequency Response | ≥60 Hz | ||
2 | Technological parameter | Power Supply(Three Phase) | 400 Hz |
12 V | |||
Power Supply(Single Phase) | 16 KHz | ||
7 V | |||
Synchronous Speed | 12,000 | ||
Power for Start Up | 4 W | ||
Operating Current | ≤0.18 A | ||
Synchronizing Time | ≤10 S | ||
Output Gradient | 14 mv/’ | ||
Master torquer | 7Ω | ||
Vice control torquer | 2Ω | ||
3 | Torquer scale factor | Master torquer | ≥500 °/h/mA |
Vice control torquer | ≥10 °/h/mA | ||
4 | Max.Tracking Speed | ≥200 °/s | |
5 | Output Nonlinearity | ≤0.1% | |
6 | Life Time | ≥5000 | |
7 | Operating Temperature | -10～+100℃ | |
8 | Shock Overload(8ms) | ≥50 g | |
9 | Physical Parameter | Dimension | Φ29×50 mm |
Mounting flanges | 30×30 mm | ||
Weight | ≤130 g | ||
ER-E2 Install Dimension
ER-E6 Dynamical Tuned Gyro Sensor
ER-E6 is of medium and low precision. The volume of domestic flexible gyros is the smallest, the mass is extremely light, the starting speed is fast (3s synchronization), and the anti-vibration and impact capability is very strong.It is suitable for weapon systems with extremely demanding environments such as projectiles, light and micro navigation, and also for special vehicle control in special environments.
Specifications:
Item | Performance Indicator |
Dimension | Φ16×22 mm |
Weight | ≤25 g |
Motor Power Supply | Special motor power supply |
Signal Power | 3.5V 8kHz, Single-phase sine wave |
Measurement Range | ±200°/s |
Fixed Position once starts random drift | ≤8°/h |
Torque Scale Factor | ≤4mA/(°/h) |
Rate Linearity | ≤0.5%(F.S) |
Cross Coupling | 2% |
Operating Temperature | -45℃~+60℃ |
Vibration Power Spectral Density | 0.8g2/Hz |
Impact | 7000g 0.13ms |
ERICCO is expert in high quality dynamically tuned gyro for oil and gas manufacturing and selling, who is one of the best manufacturers and suppliers of dynamically tuned gyro for oil and gas with high precision. We have a professional factory at your service.